<big id="e6er5"></big>
  • <label id="e6er5"></label>
      <nav id="e6er5"><sub id="e6er5"><listing id="e6er5"></listing></sub></nav>
      <u id="e6er5"></u>
        1. <label id="e6er5"></label>
        <xmp id="e6er5"><ol id="e6er5"><span id="e6er5"></span></ol></xmp>




      1. PLATING RESIST MR-303F油墨

        PLATING RESIST MR-303F是適合用于部分鍍金用的遮蔽的單液性, 堿性剝離型抗鍍油墨.此外也適合用于ITO用的蝕刻油墨.

         
        PLATING RESIST MR-303F is one component, alkaline removable type Resist Ink developed for masking of partial Au plating.
        Moreover, it is possible to be used as etching ink for ITO.

        Main Feature
        1. Cured film has flexibility, and available for a flexible board and a rigid board.
        2. This ink has excellent resistance to Au plating( Electro-less),since the contamination to the plating solution
        is very small, control of the solution is easy.
        3. Possible to be used as etching ink for ITO.

        Main Property

        Items Representing value Remarks
        Color Black color Visual
        Viscosity at 25 deg.C 200 dPa・s Viscotester VT-04
        Applicable Screen 150~250 Mesh Polyester Screen
        Optimum Ink thickness after drying 10~20µm Thickness Meter
        Dry Conditions 100deg.C × 10min Circulating Heat Oven
        Adhesion 100 / 100 Cross-cut,tape peel test
        Resistance to Electro-less Plating No penetration, No color change Ni Plating at 90deg.C for 30 min + Au Plating at 90deg.C for 40 min
        Remove of the cured film 1~3 wt% NaOH Solution 30deg.C × 1~3 min Dipping

        The above information obtained by actual measurement at our lab., and do not specified values.
        < Shelf-life > Main body: 6 months --- Stored in 25 deg.C or below (cool and dark place).
        Usage and handling precautions
        1. If dilution is needed due to viscosity variation during operation, dilute with exclusive reducer #70 within 5%.
        2. Drying should be done at the range of 100deg.C~130deg.C. Since drying time will vary based on s heat efficiency and ventilation capacity of used oven, please confirm your oven and set optimum condition.
        3. This resist can be used for general Ni/Au plating solution without any inconvenience.

        However, if it is used for special plating solution, it may cause the change in characteristics, depending on its composition. Please use it after checking fully.

        Flexibility test (JIS K 5600-5-1)

        Mandrel diameter 8mmφ 6mmφ 4mmφ 3mmφ 2mmφ
        Conventional products No Crack Crack Crack Crack Crack
        MR-303F No Crack No Crack No Crack No Crack No Crack

        Test board: Thickness 25µm/PI film
        Screen mesh: 200mesh polyester screen
        Dry condition: 100deg.C × 10min Circulating Heat Oven
        Ink thickness after drying: Thickness 14~16µm

        Elusion amount in Electro-less Ni Plating 

         

         ・Absorbance is high=Quantity of elution is large ・Absorbance is low=Quantity of elution is small Compared to Ni Plating new solution, absorbance peak which arise from elusion content from coated film can be confirmed at around 280nm for conventional product though, the peak can not be confirmed in MR-303F.

        <<Sample manufacture condition>>
        Test Board: 5.6cm×4cm /PI film/4 pieces
        Dry condition: 100deg.C × 10min Circulating Heat Oven
        Ink thickness after drying: About 30µm
        <<Ni plating condition>>
        Plating solution: Product made by OKUNO CHEMICAL INDUSTRIES CO.,LTD
        Dip condition: 80 deg.C × 4hr
        <<Measurement condition>>
        Testing equipment: Product made in SHIMADZU CORPORATION UV-1800
        Kind of measurements: Absorbance
        Measurement wavelength(nm): 200~900

        ITO-proof etching liquid test 

        <<Sample manufacture condition>>
        Test Board: ITO/PET film
        Screen mesh: 200mesh polyester screen
        Dry condition: 100deg.C × 10min Circulating Heat Oven
        Ink thickness after drying: Thickness 10~15µm

        ≪ITO etching liquid condition≫
        Etching solution: Mixed acid ITO-02 Product made by KANTO CHEMICAL CO.,INC.
        Dip condition: 45deg.C × 4min
         ≪Remove of the cured film≫
        Remove solution: 3wt%NaOH
        Dip condition: 30 deg.C × 1min
        ≪Measuring instrument condition≫
        Measuring instrument Product made by YOKOGAWA ELECTRIC CORPORATION DEGITAL MLTIMETER 755S

        Stripping test after thermal resistance 


        <<Sample manufacture condition>>
        Test Board: PI film・ Glass epoxy copper foil
        Screen mesh: 200mesh polyester screen
        Dry condition: 100deg.C × 10min Circulating Heat Oven
        Ink thickness after drying: Thickness 10~15µm
        Additional heating condition: 180℃×1-5hr/ Heat circulation oven
        ≪Remove of the cured film≫
        Remove solution: 3wt%NaOH
        Dip condition: 30 deg.C × 1min
        Check strippability: Visual

         

        CST (Asia) Limited  電話: 深圳: 0755-2308 6405 蘇州: 0512-52821513 香港: 00852-2602-6173
        地址:香港新界沙田火炭穗禾路1號豐利工業中心4字樓13室  在線QQ:  893008608
        Copyright(C) 51Touch.Com All rights reserved   技術支持:觸摸屏與OLED網   電話:13183843395
        名站導航: 觸摸屏與OLED網 | 觸摸屏B2B | 觸摸屏論壇 | 觸摸屏人才 | 觸摸屏雜志


        客服:
        樱桃视频污黄无限看最新版下载,免费网页一卡二卡,青柠在线观看视频在线观看,香港经典a毛片免费观看,yellow字幕网中文字幕 随州市| 齐齐哈尔市| 宣汉县| 泗洪县| 富顺县| 霍山县| 德惠市| 新泰市| 南昌县| 黄山市| 淮北市| 龙游县| 磐石市| 都兰县| 临桂县| 古蔺县| 扎赉特旗| 翁源县| 黔西| 汝阳县| 都江堰市| 龙井市| 舟曲县| 康平县| 莱西市| 大化| 禄丰县| 东至县| 贺兰县| 当阳市| 永仁县| 抚顺县| 莱阳市| 武陟县| 鄂州市| 德化县| 松原市| 昌图县| 客服| 汉源县| 龙海市| 洛扎县| 衢州市| 沐川县| 基隆市| 闽清县| 清新县| 中牟县| 油尖旺区| 娄烦县| 宝应县| 中西区| 策勒县| 清水河县| 美姑县| 土默特右旗| 阿瓦提县| 开封市| 岐山县| 淮北市| 鸡西市| 同德县| 建始县| 峨边| 峨眉山市| 兴国县| 长阳| 曲阜市| 城步| 磴口县| 嵊州市| 贵阳市| 枝江市| 榕江县| 抚顺市| 温泉县| 新蔡县| 淮南市| 达尔| 萝北县| 临泉县| 广灵县|